JET DROPDECK TRAILERS

Jet Dropdeck Trailers

Jet Company specializes in standard as well as custom designed trailers. We offer Dropdecks and Double Dropdecks in a wide choice of sizes, configurations and colors. Our high performance trailers are designed for Big Payloads. Working with customers is Jet's specialty.

What makes JET Dropdeck Trailers better than the competition:

  • Advanced Engineering (stronger, lightweight, heavier payload)
  • High resale value
  • Quality workmanship
  • Proven performance (Jet tested trailers with 115,000 lbs. of steel in an 8' area over a grueling test track to insure reliability.)
  • Specialized trailers to fit your needs
  • Pride and satisfaction knowing you're working with a reputable company that has been in business since 1952.
  • Customer service - at Jet Company we're always looking for tomorrow's business.

Standard Features

  • Up to 53' (longer lengths upon request)
  • 96" or 102" standard
  • Main Beam - High strength material. Ranges from 24"-28" deep in center.
  • 4" high strength aluminum extrusion or 4" high strength steel. Crossmembers are available on 12", 14", 16" or 18" centers.
  • 6" side high strength aluminum extrusion, 6" steel channel, 8.2 lbs./ft. The siderail is the winch track on both sides.
  • Rubrail - 3/8" x 2-1/2" high strength aluminum extrusion or 3/8" x 2" steel
  • Stake Pockets - Spaced 24" apart with pipe-spool. ID 1-5/8" x 3-7/16"
  • 30" Kingpin standard. Other settings available.
  • Axles - 22,500 lb rating for spring suspensions, 24,000 lb rating for air ride suspension
  • Air ride suspension available in closed tandem or 10'1" spread. Spring suspension available in closed tandems.
  • Two speed landing legs. Ultimate load capacity 140,000 lbs.
  • 1-1/4" extruded aluminum floor, 1-1/8" apitong floor or 2" nominal oak floor. 5/16" zinc plated floor screws
  • Kneebraces approximately every 4' supporting outside rail
  • Mylar tape is placed between steel and aluminum components. Aluminum components have a natural finish.
  • Protected wire harness lights. Sealed tail lights. Sealed marker lights. All connections are sealed. Rear lights enclosed in protective closures.
  • Heavy duty rubber bumpers, located on outside corners.
  • Mudflaps on both axles on 10'1" spread, Anti sail type

Options

  • Tire Carrier
  • Beavertail
  • Lift Axles
  • Winch Straps
  • Sliding Tandems
  • Manual Dump Valve
  • Air Ride Suspension
  • Spring Suspension
  • Closed Tandem
  • Coil Package
  • Lower Deck Heights
  • Twist Locks
  • Tool Boxes
  • Spring Assist Hinged Ramps
  • Load Levelers
  • Dura Lite Hubs w/Centrifuse Drums
  • Dual Tire Equalization System
  • Manual Raise and Lower Valve
  • Additional Side Marker Lights
  • 2" Nominal Oak or 1-1/4" Apitong Floor
  • Bulk Head
  • 12-1/4" x 7-1/2" Axles
  • Sliding Winches
  • Rope Hooks
  • Recessed Tie Downs
  • D-Rings
  • Intraax Suspension
  • 10'1" Spread
  • Optional Colors
  • Aluminum Wheels
  • Additional Rear Lights
  • Tail Roll
  • Tri Axle
  • Ramp Holders
  • Slanted Drops

Standard Beam Rating*

  4' 10' 20' Evenly Distributed
Concentrated Weight in Feet Ratings based on a 48' trailer with 3/8" x 5" top and bottom flange with 10'1" spread and 30" kingpin
  50,000 lbs. 53,000 lbs. 58,000 lbs. 80,000 lbs.

*Higher Beam Ratings are Available